Models and makes of sewing machines may differ somewhat, but their fundamental features are remarkably similar; consult your machine's manual for specific instructions for care and cleaning.
1. Bobbin and bobbin case: The bobbin is wound with thread that will make up the underside of a machine stitch. The bobbin case holds the bobbin, and is usually not interchangeable between machines. Use only bobbins recommended by the manufacturer for your particular model.
2. Slide plate or bobbin cover: Depending on the machine, a slide plate or hinged bobbin cover allows access to the bobbin.
3. Presser foot: This removable foot keeps fabric in place as you sew. Different feet are appropriate for various sewing techniques or fabrics. For example, a roller or nonstick foot is used for sewing leather and oilcloth smoothly.
4. Needle and needle clamp: Sewing-machine needles are removable and come in a variety of sizes. The clamp holds the needle in place.
5. Throat palate: This metal plate, sometimes referred to as a needle plate, sits below the needle and presser foot. A small opening in the plate allows the bobbin thread to come out and the needle to pass through to make stitches. Most throat plates have small lines notched to the right of the presser foot; these serve as guides for seam allowances and for sewing straight lines. The plate can be removed to clean underneath.
6. Feed dogs: These small metal or rubber teeth pull the fabric between the presser foot and throat plate, and also regulate the stitch length by controlling how much fabric passes through at once. Always allow the feed dogs to move the fabric as you guide it -- manually pulling may cause the needle to bend or break.
7. Tension regulator: This dial controls the tension on the top thread. With proper tension the top thread and bobbin thread will join together in uniform stitches. If the tension is set too tight, the stitch will pucker and break; if set too loose, the stitches will be too loose.
8. Take-up lever: The top thread passes through this metal lever, which moves up and down in tandem with the needle. Depending on the machine, the take-up lever may protrude from the front or be hidden inside the plastic casing. Before placing fabric under the presser foot, raise the lver completely (the needle will be at its highest point); this will keep the handle from snagging the fabric.
9. Bobbin winder tension disk: On machines that have an external bobbin winder, this disk helps guide the thread between the spool and the winder.
10. Bobbin winder: The small spool is placed upon this while the bobbin is being filled. To ensure that the tread winds evenly, always start with an empty bobbin.
11. Thread guides: From the spool, thread passes through these metal loops to help regulate the tension of the thread.
12. Spool pin: This small dowel holds the thread. Some machines come with several spool pins for decorative or twin-needle sewing. Spool pins can be horizontal or vertical.
13. Flywheel: This knob, also called a handwheel, raises and lowers the take-up lever. Always turn the flywheel toward you.
14. Stitch selector: On older machines, a dial allows you to choose between different machine stitches. Newer machines have buttons to select stitches.
15. Stitch-length selector Use this dial or lever to set the length of the stitches on manual and some electronic machines. Stitches are measured differently, depending on the machine. They may be measured per inch, by metric scale, or simply numerically from 0 to 9. For general sewing, use medium-length stitches; for fine fabrics, shorter stitches; for heavier fabrics, or when basting or gathering, use long stitches.
16. Stitch-width selector This dial or lever controls the width of decorative stitches, such as the zigzag stitch.
17. Menu screen On newer electronic and computerized machines, the menu screen allows you to adjust functions and stitches, sometimes replacing the separate stitch, stitch-width, and stitch-length selector dials.
18. Reverse-stitch button Pressing this button reverses the direction of the stitches, allowing you to secure the thread at the beginning and end of a seam. (Some manuals call this a backstitch button.)
19. Foot controller The speed of the stitches is partially controlled by pressing on this pedal.
When guiding fabric over the throat plate, keep your fingers at least an inch away from the presser foot at all times. If you pause between stitches, take your foot off the foot controller, so that you don't accidentally set the needle in motion. If you are taking a longer pause, turn the machine off completely.