No Thanks
Let

Keep In Touch With MarthaStewart.com

Sign up and we'll send inspiration straight to you.

Martha Stewart takes your privacy seriously. To learn more, please read our Privacy Policy.

Project

Sparkling Snowman Treat Boxes

Sparkling snowmen make an impressive display (the big figure stands more than a foot tall) and double as treat boxes for candies.

Introduction

Measurements: The spheres for these frosty figures come in different sizes. The large snowman has a 4 3/4-inch round treat box as its base, with 2 foam balls on top: 4 inches and 3 inches. The small one has a 4-inch round box and a 2 1/2-inch foam ball.

Materials

Steps

  1. Step 1

    mld105105_1209_snowman1.jpg

    Indent 1 end of a pressed-paper box with your thumbs, to help the snowman stand up. Paint both halves of box with white acrylic paint; let dry. Slice off 1 end of each foam ball using a craft knife; indent sliced end of each ball with your thumbs. Reassemble box. Using a hot-glue gun, affix 1 or 2 foam balls, depending on the size snowman you're making.

  2. Step 2

    mld105105_1209_snowman4.jpg

    For the features: Roll black modeling clay into tiny balls for the eyes, buttons, and mouth. For the nose, roll orange clay into a carrot, making ridges with the back of a craft knife. Bake following manufacturer's instructions. Using the tip of a paintbrush handle, poke holes into the foam balls to mark the placement of clay pieces.

  3. Step 3

    For the arms: Print and cut out snowman templates (Large Snowman Template or Small Snowman Template). Trace arms onto white card stock; cut out. Using the hands as a guide, cut 4 mitten shapes from wool felt. Using craft glue, affix 1 mitten onto each side of each hand; let dry. For mitten cuffs, cut 2 lengths of narrow ribbon. Wrap 1 around each hand where mitten meets arm, securing with hot glue; let dry. Set arms aside.

  4. Step 4

    For the scarf: Cut a strip of wool felt (1 1/4 by 14 inches for the large snowman; 1 by 12 1/2 inches for the small one). To make fringe along the length and width of scarf, pull 1 to 2 threads on the long edges and a few on the short edges.

  5. Step 5

    mld105105_1209_snowman3.jpg

    Construct the hat: Trace 2 hat templates (Large Snowman Template or Small Snowman Template) onto gray card stock; cut out. Using a bone folder, make creases along the rectangle's dotted lines. Using craft knife, cut tiny notches along long edges, up to folded edge.

  6. Step 6

    Following circle template and using craft knife, cut out the inside circle, creating the brim and the top of hat. Roll rectangle, overlapping it at the short edges. Slip it inside brim; flatten the notches underneath brim, and secure with craft glue. At the other end of rolled rectangle, fold notches in, and glue on hat's top; let dry. Paint white "snow" on the edges of brim and top of hat.

  7. Step 7

    mld105105_1209_snowman5.jpg

    Separate halves of box. Using a craft brush, apply craft glue to part of snowman's body. Holding snowman over a bowl, sprinkle spoonfuls of clear shard-glass glitter over glued area. Repeat until entire body is glittered; let dry. Glitter both arms above the ribbon cuffs, front and back, except at the inner top area of each arm, where arms will attach to body. Glitter the painted areas of hat. Attach arms to body at the shoulders, using hot-glue gun. Hot-glue hat to snowman's head.

  8. Step 8

    mld105105_1209_snowman8.jpg

    Arrange accessories: Using tweezers and craft glue, insert features and button pieces into the prepoked holes. Place a trinket, such as a vintage bottlebrush tree or a bundle of sticks, under 1 arm if desired, and secure to body with hot glue. Secure hands to body or trinket with hot glue. Tie scarf around the neck.